#Iei keypad 212i install
#Iei keypad 212i professional

All programming can be performed from the front of the keypad. Our New Jersey & NYC Services: Commercial & Residential Door Repair & Installation Intercom, Access Control and CCTV Installation and Maintenance Commercial. This feature does not work with the master code. The unit comes equipped with three LEDs that indicate operation status and visual PIN entry confirmation. Keypad active is a negative voltage output (sink) available on terminal (or wire) marked WB (see wiring diagrams for location). Write a Review 120 users Single gang design 1 SPDT 2 amp relay and three 50mA negative voltage outputs Optional 293 relay board converts 3 voltage. Simple programming shall allow the output to toggle (by code) or time from 1 to 90 seconds. IEI 212I Indoor Flush-Mount Keypad Also known as: IE-212I IEI's 212i is a cost-effective, indoor, flush-mounted keypad designed for light duty access control environments. Linear Indoor Flush-mount Keypad 212i is an affordable single door access control keypad designed to meet the indoor flush mount needs of lighter volume. The lock release relay shall be rated at 8 amps and shall be tough enough to handle any locking device. This output may be wired to a siren, buzzer, guard station, camera or any other device. This can be turned off through programming. The system shall alert the resident to any 'propped' door by energizing a 1 amp Form 'C' relay. The system's propped door relay shall be programmable for a 1 to 15 minute time window in which the door may be held open after a valid entry. This output can be programmed to energize for up to 15 minutes or latch. Codes may be from 1-6 digits in length and digits may be repeated.Īssisted by the door position sensor input, this 1 amp Form 'C' relay shall energize if the door is opened without a valid user entry or egress input. The keypad memory shall have nonvolatile EEPROM memory for up to 120 users.

#Iei keypad 212i professional

It comes with Hub Manager® Professional software, has a 12-15 VDC operating power system, a real-time clock, and it includes 800 event buffers.The access control system shall be Alpha Communications®/IEI model 212I keypad or approved equivalent. 5.0 out of 5 stars based on 2 product ratings. The access system accommodates up to 2000 users per door with a network capacity of up to 32 doors per site via RS485 communications. item 7 3 IEI 212i Indoor Flush-mount Digital Keypad 3 Circuit Boards LEDS 3 IEI 212i Indoor Flush-mount Digital Keypad 3 Circuit Boards LEDS. The ProxPad is a fully integrated single door access control system that combines keypad control panel and proximity technology to create a secure access point for entry or exit. Door-Gard has the added benefit of being easily programmed with any of our products, thanks to its advanced engineering and design. I designates flush mount indoor style of keypad as opposed to se or sealed environment style, or r for rugged style which has a cover and box mount. Newer VIDIR Carousels will have the ubble Keypads.

Use the included tie wrap to bundle all the wires together from the keypad wire harness and relay board. The IEI 212i Keypad is mostly found on older VIDIR Carousels.

The relays must face up towards the keypad wire harness connector P2.

#Iei keypad 212i install

Door-Gard is an electronic lock that is being successfully utilized by thousands of companies throughout the world for stand- alone operations. 212iLW & 242iLW Standalone Keypad Installation & Programming Manual To install the relay board, plug the relay board onto P3 on the keypad. This includes the top-rated security keypad lock known as the Door-Gard, one of our most popular, high-quality security system solutions.

ENVIRONMENTAL: TEMPERATURE: -20☏ TO 130☏ (-28☌ TO 54☌) IEI recommends using a filtered and regulated power Indoor Only. Whatever your specific environment or application, we have a broad, proven selection of Access Control System devices and accessories. cannot ground the power supply, then you must ground.